Bog Pod Death Grip for prime rut Moose Hunting in Newfoundland

Posted on by

The Bog Pod™ Death Grip™ is like having a “bench rest” in the field. This is the carbon fiber model. Yes it is a bit heavy at 7.5 lbs and perhaps little clunky to carry but once it is set up you are in good shape.  It retails for around $280. Not cheap but on a trophy hunt it fits the bill.

But more than that, the Death Grip vise holds my rifle allows me and my hands to be free.  In my case, i expect to use it to hold my 375 Ruger while calling a rut crazed Newfoundland Bull Moose into shooting range from say a half mile away.

The spongy tundra is tough enough to walk in and small European spruce call Tuckamore’s which are small, thick, and knarly. .Accordingly, seeing above and around the tuckamore’s with a tripod or bipod is likely a great help. The feet are rubber and a shaft is threaded through the rubber with a metal point if you need more than the rubber feet to hold the tripod steady.

The tilt and pan can be tightened so that you can hold on target.  I shot three rounds at 150 yards at a 40 inch long brown piece of cardboard with no target bullseye. Similar to the side of a moose, and placed all 3 shots within 6 inches in the lower 1/3rd of the target.

I believe a setup with the Death Grip for Moose is ideal because it can take time for a moose to respond and head your way. Leaving you to call with hands coned over your mouth while the Death Grip holds your rifle at the ready.

Good Hunting!

© All Rights Reserved

Bought another Boat

Posted on by

In case you are wondering why I have not written any articles in the past few weeks is because I have purchased a used boat, shown above. It is a 2012 Sea-Fox 16 ft with a 2012 50hp 4 stroke Mercury. I bought it for lakes and coastal ocean fishing and pleasure. I have had a 25 ft Tiara Pursuit previously and it was too much for me to handle alone.

Recently we put in at Cashmans Park in Newburyport and fished for mackerel as bait and striper fished near the mouth of the river.  I caught a small striper and tossed him back. The 50 horse is adequate and gas friendly. I hope to do more with family and get them away from phones and electronic gadgets and x-boxes. The boat came with a hummingbird GPS and fish/depth finder but did not come with the coastal chip card for the GPS part so I ordered the chip at a cost of $125 dollars. In the Merrimack River and for coastal excursions it is essential!  On return to my home we wash it down with fresh water and run the motor with a fresh water hose. More later…

 

 

Summertime Outdoors for Kids… A hope for the Future

Posted on by

Children these days are not being educated as much as they are being indoctrinated in our left leaning public education system. In particular hunting and outdoor sports are often not in most teachers vocabulary and look down on it. Summertime and your time is now; for parents and grandparents to step up to the plate and dedicate fun time with your children outdoors. Camping, Hiking, Fishing and the introduction to the shooting sports are great ways to get kids away from the almighty X-Box.

I just purchase a 16 ft motor boat for fishing with them on the ocean and in our local lakes and ponds. I am determined to get them hooked on the value of Outdoor Life. I hope that you are too. Don’t forget involvement with Scouting and 4H opportunities. Both organizations are involved in summertime shooting sports.

 

Walking the String with Longbows and Recurves

Posted on by

Recently I purchased recurves for my grandkids and a 45 pound recurve for me to play with them. No sights just the bare bow. I have spent years shooting bare bow but gravitated to the compound bow and rifle for longer distance hunting accuracy.

Shooting instinctive, barebow there are no sights but you can train yourself to see the sight picture as a gap that your brain can calibrate to. Point, draw/aim and shoot. As a youngster I learned to shoot split finger where the index finger was above the arrow knock and two fingers below. Drawing back the bow so my index finger touched the corner of my mouth as an anchor and then released. This worked ok but I found that shooting tight groups accurately helped to shoot three fingers under the arrow. As you can use the arrow to sight down it. With training you can be a great shot but it takes dedication.

I use a technique called “Walking the String” some call it Apache Draw, here you place your three fingers under the arrow, then use your thumb to mark where the split in the finger tab is. About an inch below the arrow. Draw the bow an  inch below the arrow, then use the arrow to sight the target. You can angle or cant the bow a bit if it feels and sights better. Secondly you can use a stance that is quartering toward the target with your feet a shoulder width apart with your knees slightly bent and loose like a spring. Set your distances at 15, 20 and 30 yards and establish your form and accuracy at 15 yards then 20 etc.. I use helical 4 inch feather fletch arrows as I will later put broadheads on them.

Now practice, practice, and practice.

Good Shooting!

 

 

Moose Cartridge Caliber and Bullets – Updated

Posted on by

Many articles later, the most popular Moose caliber I observe is the venerable, time tested 30-06 Springfield with 180 grain bullets on your average Moose for your average Moose hunter. Moose have been cleanly killed with cartridges of lesser energy but those kills were best taken broadside such as the 308 Win, .270 Win and 7mm-08 and 6.5 Creedmoor are most common. Of course the Swede’s love the 6.5 – 55 Swedish Mauser but we aren’t in Sweden. We are in North America East in Newfoundland, Canada.

If you you-tube for bull moose kills with rifle, you will often see multiple shots taken and hits to the lung area too. Moose are hard to fall where the shot was taken.

Shot Placement – Top of Heart center Lungs as shown.

It is essential to shoot as accurately as possible. It is shot placement that kills Moose when coupled with adequate penetration and energy. Bullet construction should be such that when the bullet mushrooms and expands that it stays together as it penetrates. Bonded, Partition and All Copper style bullets are recommended. I am a fan of Nosler Bullets such as the E-Tip Solid Gilding Copper, AccuBond and Partition.

Bullet Energy – If you follow some Fish and Game recommendations used to be around 2500 ft lbs (recommended). I assumed delivered energy. Now some F & G officials suggest 2200 to 2500 ft-lbs of energy at the muzzle however I believe this is very misleading as the shooter should know his energy limits when the bullet strikes the moose at longer ranges. In the case of elk, terminal energy is recommended at 1500 ft -lbs. Moose should be more like 1800-2000 ft lbs delivered or better with velocities around 2000fps.

The 30-06 is not ideal for the largest of Moose in all situations, particularly quartering away. Shoot a cartridge that gives you the most options. If you can handle larger calibers and recoil such as the 300 Win Mag or larger then you shot options increase dramatically. Do you have to? Of course not, you may have to wait to get closer or change the shot angle. A 30-06 180 grain bullet with a Muzzle velocity of 2600 fps delivers around 2000 ft-lbs at 200 yards. So that would be a suggested max range. 

My hunt outfitter says shots are 40 to 300 yards. At 300 yards a 180 grain 30-06 delivers around 1700 ft-lbs. A 300 win mag will deliver over 2000 ft lbs at that range.

Of course if you cant handle the recoil of big magnum rifles  and cant shoot them accurately, then don’t shoot them! Note: There are many recoil pads on the market today to cut recoil in half. So before shooting these heavy recoil rifles always do some homework on recoil management. You will be glad you did!!! Pachmayr makes the Decelerator™ one of my favorites for heavy recoil.

The 7mm Rem Mag and 7mm STW, 7mm Wby Mag 7mm RUM are great on the largest of 300 yard Bull Moose as is the The 28 Nosler (.284) which spits a 175 grain out at 3100 fps and can hit the 2500 ft-lb delivered energy at 450 yards. Wow!

The 8mm Rem Magnum with 180 grain bullets can reach to 300 yards near to 2500 ft-lbs delivered enegy. Nice!

Many 338 Mags below can throw a 225g bullet to 400 yards near 2500 ft-lbs. I shot the .338 Win Mag in Africa; 338 Win Mag, 340 Weatherby Mag, 338 Rem Ultra Mag, 338 Lapua Mag, 33 Nosler or the 338-378 Weatherby Mag all do a great job.

The .358’s such as the 350 Win Mag, 358  Norma Mag, and 358 STA -Shooting Times Alaska  all do that!  The 358 STA shoots a 225 grain bullet at 3000 fps out to 375 yards at just around 2500 ft-lbs.

My .375 Ruger or a .375 H&H hurles a 260 to 300 grain bullet to 300 yards with 2500 ft-lbs and the 300 grain bullet does so with a sectional density of .299 that rates highest in penetration. The .375 Ruger and .375 H&H are geared for Cape Buffalo or 1200 plus lb Bull Moose or a 2000 lb Bison. Alaskan Guides like the .375’s around Brown bear too.

My Newfoundland bull fell after the first shot with my 375 Ruger with 300 grain Nosler AccuBonds in less than 10 seconds. It was a quartering toward shot smashing the front shoulder, fully mushrooming, wrecking the lungs and piled up on the skin on the far side while still maintaining 80% of its weight. Note: I shot him in a snow squall in near whiteout conditions in a 20 mph wind in my face at 100 yards (wind chill below zero) .  His rack was small but a big body! I decide to take him as I did not want to hunt a full week in these conditions. My friend Oliver, on the left,( just turned 80 years old before the hunt) took a cow at 200 yards with his 7mm Rem  Mag. the next day. He too was not willing to hunt longer than he had to in these conditions.

The 45-70 does not meet the 300 yard criteria but a great close Moose killer for years.

The off-the-rounds in the .400 class are often designed strictly for dangerous African game and can be used on big Moose but are not necessary. Of course if you hand load then you can load the 458 Win Mag down to equal the 45-70. It is the same caliber. It’s your hunt! Have Fun!

Good Hunting!

© 2019 All Rights Reserved.

 

 

Revolutionary War Pennsylvania Flintlock at 150 yard Target- Updated

Posted on by

As most are aware that I have been shooting my “self built top-of-the-line kit” 50 cal. Jacob Dickert Lancaster Flintlock (from Jim Chambers Flintlocks Ltd.) of late for fun and experimentation to improve accuracy and reliability. I have named the rifle Cricket

Just prior to this article I had to open the flash hole a bit to 1/16th inch on Cricket to improve reliability of ignition in the deer woods. I now have 100% ignition. Heaven forbid a flash-in-the-pan and no bang and no deer! The accuracy of this rifle has been great but I wanted to experiment with a slightly thicker patch to get better spin on the 50 cal. 177 grain round ball to see if I can tighten the groups a tad. I was getting 4 inch groups at 75 yards with 0.015 Wonder Lube patches  and 90 grains of FFG.  I purchased some 0.018 Wonder Lube Patches a few weeks back and at 50 yards bench rest I cut the x on the target with my first shot. Yes Open sights that I created! I was so thrilled! My nephew said, looking through his scope that he couldn’t see the hole. He looked everywhere except the dead center. I stopped shooting so as not to jinx the next shots and helped him sight his Ruger M77 in 7 MM Rem Mag for a Texas Wild Pig Hunt. A week later I took the Flintlock back to the range and decided to go for 100 yards and then 150 if all worked out. There I met Vince Natale a club member that was just crazy about Flintlocks and their Revolutionary war history, just as much as I was. We talked and talked. Vince said; I will spot your 100 yard shot! My rifle kicked, and Vince shouts, great hit, high in the bullseye. I said, well I purposely aimed a bit high figuring for some bullet drop. Ok, lets move the silhouette target to 150 yards, I said eagerly. This for target only as it has insufficient energy for deer hunting at that range.

The 2 Shots struck the target low but grouped at 4 inches. Vince was very impressed. I needed more data.

UPDATED

Not enough for a real group, I went back and shot again this week with sunshine and little wind. My point of aim (See Below Target) was the upper bullseye at 150 yards and measured the drop at the lower edge of the bottom target at 17 inches at the lowest and average drop for the group was around 14 inches. I put the front sight level with the notch at the rear using 90 grains FFG and a .490 Hornady round ball patched with a .018 wonder lube patch (.45 to .499) patch diameter. The bullets were tight to load in the barrel than normal but achievable. The barrel was swabbed with a saliva spit patch and dry patch using both sides of the patch after each shot. I shot 4 shots for group and they look to be grouped about 6.5 inches apart in the lower left target. I adjusted the rear sight a tad to bring the bullets closer to center line and lifted the front sight just above rear sight and took a shot. You can see the bullet hit the lower target in the upper left quadrant about 2.5 inches left of center and 7.5 inches low. I drew a picture of what it looked like as I sighted the rifle.

I played with some assumptions using JBM Ballistics Software after finding some on line data (http://www.namlhunt.com/traditionalmldata1.html) for 50 cal Tennessee flintlock with a 41 inch barrel  mine is 44 inches) and they chrono 1861 FPS Muzzle Velocity with the same round ball (est BC 0.068) and 90 grains black powder and a .015 patch. That bullet drops 12 inches at 150 yards says my JBM software and at 200 yards it drops 31.7 inches and has 276 ft-lbs of energy. At 300 yards the bullet drops 111 inches and has 188 ft-lbs of energy.

For hunting whitetail deer modern day experts suggest approximately 1000 ft-lb minimum as an energy guide for deer and with that said,  I should limit shots at around 30 yards with the 50 cal round ball. Ridiculous! Of course we know that deer are taken out to 100 yards with round ball every year but data says the average shot here in New England is around 40 yards or so. At 50 yards most traditional muzzle loaders of the past achieve just over 800 ft-lbs at 50 yards yet these older muzzle loader flintlocks and caplocks have been cleanly killing deer size game beyond that 50 yard mark for centuries. Just use some common sense!

Good Shooting!

 

Flintlock: Understanding Flash-in-the-Pan no fires and simple fixes.

Posted on by

The ubiquitous Flash-in-the-pan or No-Flash-in-the-pan was coined perhaps around the time of the American Revolution or likely earlier. For me, as a hunter, this is intolerable. Here in New  Hampshire, Deer are not as plentiful as our southeastern states, so having a flash- in-the-pan no fires in the deer woods is no fun!

But it need not be so!

My fix was simple after tons of internet research, changing my flint grip from leather to lead helped but it was to drill the touch hole to 1/16 inch or 0.0625. This is slightly larger than the original touch hole. See the website below. Also do not cover the touch hole with priming powder! My shot groups at 75 yards are around 4 inches with open sights. I don’t expect to exceed 50 yard in the local deer woods but a steady rest bipod or tree branch will help.  

https://www.muzzleloadingforum.com/threads/drilled-touch-hole.27721

My Flintlock (Cricket) is a true Lancaster Pennsylvania Rifle of Jacob Dickert fame, some call it the Kentucky Rifle of Daniel Boone and Davy Crockett fame.

Here, after a shot it looks a bit dirty, like this but you can see the touch hole larger to 1/16 inch which appears to have cured the ignition problem. Others instruct to run a spit (spit saliva) patch after each shot and then a clean patch. That works for me. Black powder residue is very dirty and cruddy but works the best in a Flintlock and patched round ball. Save the Pyrodex for your in-line muzzleloader.

I built this rifle from a very high end kit from Jim Chambers Flintlocks Ltd. My Flintlock came with a threaded device called a threaded touch hole liner and named White Lightnin’ to improve ignition by which the flash of powder in the pan would ignite the main charge in the barrel. The original hole itself is smaller than 1/16 of an inch.

My Flintlock is basically new (70 rounds fired) and had as many ignitions as I did of flash pan misfires. Cleaning the barrel and vent hole was done at every shot and even then had misfires. If the hole itself if not placed correctly with the pan, it is a problem but can be resolved. My touch hole was placed correctly, as far as I can tell but still misfired so I drilled the hole to 1/16 inch and basically cured the ignition problem to a large extent.  Every rifle is different. Some experts open the hole right away to 1/16 inch others shoot it till it widens over time. As a deer hunter I want it all the time. The touch hole can be opened further, see the website above but if too large will cause loss of pressure and slower ignition time, delaying the ignition. The great thing with a touch hole liner is that it can be replaced.

Good Hunting!

 

Samick Sage Takedown Recurve – Out-of-the-Box – Balloon Shoot

Posted on by

Traditional archery is a great way to begin shooting bow and arrow. My oldest grandson just turned 13 years old. He has had starter bows for children in the past and loves to shoot.  He is a big and tall boy at 5 ft 10 inches already. I purchased two new Samick Sage bows (one for me) in 45 lb weight at 28 inches draw, a shooting glove/arm guard and some right hand helical fletched xx75 aluminum arrows.

http://www.lancasterarchery.com/galaxy-sage-takedown-recurve-bow.html

Out-of-the-box the bows were mighty handsome! The laminated wooden riser was machined expertly and the limbs are laminated maple and fiberglass. Instructions for installing the upper and lower limbs were easy.

The bow came with 2 brass string knocking points and a nice stick on rest that alignes with the riser hole for a plunger known originally as a Berger Button.

At $119 dollars this is a bargain and a great value!

We use the bows traditionally to shoot target at 20 yards and chase and shoot floating/ moving balloons with Judo points that keep the arrow from burying itself in grass.

What a great summer fun time chasing balloons at various ranges on  my back lawn.  All in prep for hunting game! My grandkids in the back yard below.

 

Good Shooting!

 

 

 

 

Savage 110 Apex Storm XP W Vortex Crossfire II Scope Out-of-the-Box with 140g Nosler AccuBond

Posted on by

https://www.savagearms.com/content?p=firearms&a=product_summary&s=57340 

The Savage 110 Apex Storm in 6.5 Creedmoor arrived for Test and Evaluation just as you see it above with the Vortex Crossfire II Scope, and Picatinny rail mounted and bore sighted right out-of-the-box. It is a very smart looking stainless barrel with button-rifling and adjustable synthetic stock. It weighed in at 7 lb 7 oz. with my Lyman scale. The AccuTrigger breaks at 3 lb 8 oz. Nice for a hunting rifle! The bolt assembly below is jeweled and has a knurled bolt for a good grip.

The bolt lugs are state of the art. The action is very smooth! It has a detachable metal and synthetic clip that makes an audible click when it is inserted. The Stainless Barrel has a non-reflective mat surface so you don’t spook game.

 

These are things that you would find in a more expensive rifle.

Savage says:

“The platform provides accuracy and adjustability like no other package rifle thanks to the Savage® AccuTrigger™, thread-in heasdpacing, floating bolt head and button-rifled stainless steel barrel. Plus, its length-of-pull can be easily adjusted to fit any hunter for better comfort and consistency. ”

Out-of-the Box first 100 yard 3 shot group with Nosler’s 140 grain AccuBond is a solid 1 inch.

FEATURES

  • Redesigned Model 110 rifle
  • Stainless steel button-rifled barrel
  • 3-9x40mm Vortex Crossfire II scope, mounted and bore-sighted
  • Dead-Hold BDC reticle’s hashmark design reduces guesswork on holdover and windage
  • Vortex Hunter medium rings and one-piece EGW 0 MOA rail
  • User-adjustable AccuTrigger
  • Adjustable length-of-pull
  • Modern ergonomics
  • Detachable box magazine

The MSRP is just $749.  Wow!

I give this Out-of-the-Box Test an A+

This is a fine rifle/scope combination that anyone would be thrilled to own and is a great value!

Get one now before they are gone!

 

Savage Model A22 in 22LR -Out-of-the-Box with CCI Velocitor’s

Posted on by

The A22  comes in 22 magnum and 22LR. We are testing the 22LR with CCI Velocitors with a 40 grain hollow point.

https://www.savagearms.com/content?p=firearms&a=product_summary&s=47200

The Savage A22 appears to be a well made basic Semi-Auto production rifle. Out of the Box I added a 3×9 Scope to test it. Weaver bases were pre-installed. Scope bases are picatinny type thus making scope swaps easy from one rifle to another these days. The barrel is pictured with a front sight. Mine had no front sight as it  was intended for scope only.  The price of $284 dollars is terrific for the features provided. The only feature that was lacking in my mind was the adjustable accu-trigger. I could not get it to adjust lower than 3 lb 10 oz. from the original 5 pounds it came with but performed crisply.

I am very impressed with the A22 as it shoots CCI Velocitor ammo at around 1400 fps and with great ease and accuracy. Wow!

The A22 with CCI Velocitors – Good for Coyote? I think so as there are several video’s that can attest.

The Savage A22 At the Range

Specifications                                    Accuracy at 50 yards/w CCI Velocitor
MSRP – $284.00                                  Group 1   1 1/4 inches
Action – Semi Auto                             Group 2   2.0   inches (probably me)
Barrel – Color Blued                           Group 3   1 1/8 inches
Barrel Finish – High Luster
Barrel Length (in)/(mm) – 22 / 558.80
Barrel Material – Carbon Steel
Caliber – 22 LR
Magazine Capacity – 10
Magazine Rotary
LOP 13 3/4
Overall Length (in)/(mm) 41 / 1,041.40
Rate of Twist (in) 1 in 16
Receiver Color Blued
Receiver Finish High Luster
Receiver Material Carbon Steel
Type Rimfire
Stock Color Black
Stock Finish Matte
Stock Material Synthetic with Swivel Mount studs
Stock Type Sporter
Weight (lb)/(kg) 5.6 / 2.54
The Synthetic 10 round rotary magazine worked very well once you get the hang of loading a few.
Again, the Savage A22  performed flawlessly with such a powerful round as the Velocitor and with great accuracy at an affordable price. The longer barrel holds bullet velocity and energy at longer ranges.
More testing with other bullet brands and at longer ranges soon.
Good Shooting!
© 2019